The first thing that you should know when building circuits for electrical devices are the theories in basic electronics. Get to know the various components used in them and how to properly connect them to each other. And study how to make and read schematic diagrams that represents graphically the electrical circuit using images and symbols.
Doing so is essential when there is a particular device you want to make but is still confused with some parts of the process. This might be something a little advance such as voltage divider which produces an output that is a portion of its input. But learn or review first the theories in basic electronics to understand better the more advanced stuffs.
Begin with identifying the types of electricity such as AC or alternating current and DC or direct current. The direction which electrical signal flows on AC is constantly reversing or alternating with the reversal rate measured in Herts. Meanwhile the flow in DC is one direction to ground from power source and found commonly with batteries.
A closed circuit is when the electric current is allowed to pass through a path from power source to ground which normally indicates a device is functioning. While an open one breaks this path and will prevent the movement just like in turning off a machine. This is done with a switch so you could alternate between them instead of removing the source.
When current pass through components, they create resistance to ground from positive voltage and if these are directly connected, this would cause the circuit to be shorted. This direct connection would result in fire, breaking, overheating or explosion which you must avoid. Putting switch would not provide additional resistance so other parts must be added.
Wiring things together could be done with two ways that are called series as well as parallel and the former indicating that every component is wired after each one. While the latter would indicate that the parts were wired next to the other which makes electricity simultaneously pass them. Both ways can be used together when you build circuits.
Resistors are used in adding resistance to circuits and reduce the current flow with them being available in different values measured in ohms. They also have wattage ratings and their value are indicated by the colored bands on their body. You may learn how to read these bands or just look up graphs that help you calculate their values.
Capacitors are components which stores electricity then when it drops, discharges them and Farads is used to measure them with common units being picofarad, microfarad, and nanofarad. The capacitor types most used commonly are ceramic disc as well as electrolytic. The former is non polarized while the latter is polarized needing one leg to properly connect with the corresponding one.
Diodes are polarized components allowing current to pass through one direction and would cause a voltage drop. One of its side is called cathode which connects to power and the other is anode. These are just samples of the basic theories you must learn in making electrical devices.
Doing so is essential when there is a particular device you want to make but is still confused with some parts of the process. This might be something a little advance such as voltage divider which produces an output that is a portion of its input. But learn or review first the theories in basic electronics to understand better the more advanced stuffs.
Begin with identifying the types of electricity such as AC or alternating current and DC or direct current. The direction which electrical signal flows on AC is constantly reversing or alternating with the reversal rate measured in Herts. Meanwhile the flow in DC is one direction to ground from power source and found commonly with batteries.
A closed circuit is when the electric current is allowed to pass through a path from power source to ground which normally indicates a device is functioning. While an open one breaks this path and will prevent the movement just like in turning off a machine. This is done with a switch so you could alternate between them instead of removing the source.
When current pass through components, they create resistance to ground from positive voltage and if these are directly connected, this would cause the circuit to be shorted. This direct connection would result in fire, breaking, overheating or explosion which you must avoid. Putting switch would not provide additional resistance so other parts must be added.
Wiring things together could be done with two ways that are called series as well as parallel and the former indicating that every component is wired after each one. While the latter would indicate that the parts were wired next to the other which makes electricity simultaneously pass them. Both ways can be used together when you build circuits.
Resistors are used in adding resistance to circuits and reduce the current flow with them being available in different values measured in ohms. They also have wattage ratings and their value are indicated by the colored bands on their body. You may learn how to read these bands or just look up graphs that help you calculate their values.
Capacitors are components which stores electricity then when it drops, discharges them and Farads is used to measure them with common units being picofarad, microfarad, and nanofarad. The capacitor types most used commonly are ceramic disc as well as electrolytic. The former is non polarized while the latter is polarized needing one leg to properly connect with the corresponding one.
Diodes are polarized components allowing current to pass through one direction and would cause a voltage drop. One of its side is called cathode which connects to power and the other is anode. These are just samples of the basic theories you must learn in making electrical devices.
About the Author:
You can get great tips for picking a voltage divider supplier and more information about a reliable supplier at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
0 nhận xét:
Post a Comment